A battery pack builder in Central Europe came to us after a pre-production pack showed an insulation fault. The copper bus bars interconnecting the cell modules were left bare copper with only a gap to the neighboring cell bracket. After vibration cycling the clearance narrowed, and the exposed copper arced against the bracket near a high-voltage section. The bar itself carried the current correctly; the insulation and clearance around it had not been engineered for the moving assembly.
We reviewed the pack layout with the customer. A bus bar carries high current in a rigid copper or aluminum shape, and its exposed edges and surfaces must be insulated against neighboring conductors, brackets and the pack housing. We reworked the bars with a matched insulation method that held through vibration and thermal cycling, kept the required creepage and clearance, and left the bolted joints accessible for service. This release covers the three insulation methods we supply for copper bus bars: heat-shrink tubing, epoxy coating and plastic overmold. It compares them on current rating, clearance, vibration, thermal performance and cost, and maps each to EV, energy storage and power distribution assemblies.
The bus bar sits at the power level of the pack, separate from the low-voltage control electronics that may run on an FPC or a membrane switch in the same enclosure. The insulation choice protects the high-current path; the control side keeps its own signal and contact design.
Why bus bar insulation matters
A bare copper bar is an efficient conductor, but in an assembled pack it sits close to other metal: cell brackets, housing walls, adjacent bars and fasteners. Vibration, thermal expansion and assembly tolerance can reduce the gap between the live bar and nearby metal. Without insulation, that reduced clearance risks creepage, arcing or a short. The insulation layer covers the bar surface, holds the dielectric separation even when the gap narrows, and protects the copper against corrosion and touch.
The insulation also has to survive the pack's environment: operating temperature, humidity, vibration and, in EV and storage systems, the safety expectations around high-voltage current. The method chosen affects how much clearance can be reduced, how the bar mounts, whether the joint stays serviceable, and what the finished bar costs. There is no single best method; the choice follows current, voltage, vibration, temperature and how the bar is assembled and serviced.

An insulated bus bar routes high current between modules: the insulation layer holds dielectric separation from brackets, housing and neighboring bars through vibration and thermal cycling.
Comparison: heat-shrink vs epoxy coating vs plastic overmold
| Parameter | Heat-shrink tubing | Epoxy coating | Plastic overmold |
|---|---|---|---|
| Insulation coverage | Tubing over bar, ends and joints exposed | Thin conformal film on surfaces | Full molded shell around the bar |
| Clearance reduction | Moderate, tubing adds wall thickness | Thin, little added bulk | Thickest, molded geometry holds shape |
| Vibration and impact | Good, can move on the bar if loose | Brittle film, can crack on flex | Best, locks bar and supports edges |
| Temperature hold | Good within tubing rating | Good on static bars | Good, resin selected to range |
| Joint serviceability | Ends and bolted joints stay accessible | Coating stripped at joints | Joint areas masked or reworked |
| Relative cost | Lowest, fast to apply | Moderate, process-dependent | Highest, tooling and molding |
| Best fit | Static bars, repairable assemblies | Flat static bars, corrosion protection | High-vibration, shaped high-current bars |

At the joint, the insulation stops short of the contact surface; the bolted or welded connection stays conductive and serviceable while the covered bar remains insulated.
How each insulation method behaves
Heat-shrink tubing is a sleeved polymer tube slipped over the bar and heated to shrink tight against the copper. It is the lowest-cost and fastest method, and it leaves the bar ends and bolted joints accessible for service. Its limits are coverage and fit: the tubing covers the straight body but leaves ends, bends and joints exposed unless separate boots are added, and a loose or poorly shrunk tube can move on the bar under vibration. It suits static or gently moving bars, repairable assemblies and cost-sensitive builds where clearance can be held by design.
Epoxy coating applies a thin conformal resin film over the bar surfaces. It adds little bulk, so it fits where space is tight and the bar sits close to other components, and it protects copper against corrosion. Its limitation is mechanical: a thin epoxy film is brittle and can crack or lift where the bar flexes, vibrates repeatedly or takes impact. It suits flat, static bars in a fixed enclosure where the bar does not move and the main need is surface insulation and corrosion protection.
Plastic overmold injects or molds a thick plastic shell around the bar, locking it into a shaped insulator with edge support and defined mounting features. It gives the strongest vibration and impact protection, holds the insulation geometry through thermal cycling, and can integrate locating bosses and mounting points. Its limits are cost and tooling: overmold carries tooling and molding expense, and joint areas must be masked or reworked after molding. It suits high-vibration EV and storage bars, shaped high-current conductors and assemblies where the insulation also locates and supports the bar.
Matching the method to the assembly
EV and high-voltage battery packs - overmold where vibration and clearance are tight; heat-shrink on accessible static bars. Pack bars see continuous vibration, thermal expansion and close packing around cells and brackets. High-voltage shaped bars usually go to overmold for the locked insulation and edge support; lower-voltage static bars can use heat-shrink where the joint needs service.
Energy storage and rack power distribution - heat-shrink or epoxy for static busbars. Rack and cabinet busbars run fixed between modules with little motion. Heat-shrink keeps joints accessible; epoxy suits flat bars that also need corrosion protection. Clearance to the rack and neighboring bars is held in the layout regardless of the method.
Industrial power and machinery panels - heat-shrink for repairable builds; overmold on vibrating machine bars. Stationary panel distribution favors the lower-cost tubing. Bars mounted on vibrating machinery or near moving parts favor overmold so the insulation does not loosen or crack over time.
Low-current control and signal harnesses - tubing or coating, not heavy overmold. Small signal bars and FPC tails do not need the molded shell; insulation there follows the conductor size and the contact design rather than the high-current pack standard.
Clearance, creepage and the exposed joint
Insulation reduces the dependence on air gap, but the voltage, the pollution level and the enclosure still set the required creepage and clearance around the bar. The insulation layer does not replace the joint design: bolted, welded or screwed connections stay conductive at the contact surface, and the insulation stops short of that surface so it does not interfere with the joint. At high-voltage levels, the material's dielectric rating, tracking resistance and temperature range are specified alongside the bar current. We review the bar, the insulation and the neighboring metal together on the layout rather than treating the insulation as a final cover-up.
Selection checklist for bus bar insulation
1. Voltage and required clearance. The working voltage and enclosure pollution level set creepage and clearance. Higher voltage and closer packing push toward a robust insulation method rather than relying on air gap alone.
2. Vibration and motion the bar sees. A bar that vibrates or moves repeatedly favors overmold or a firmly shrunk tubing; loose tubing and brittle coating fail under motion.
3. Operating temperature and ambient. The insulation material must hold its dielectric and mechanical properties across the pack's temperature range, humidity and any chemicals the enclosure sees.
4. Joint serviceability. If the bar must be disassembled or re-torqued in service, the method leaves the joint accessible; overmold around a serviceable joint adds rework cost.
5. Space and bar geometry. Shaped, bent or profiled bars need a method that follows the geometry. Thin coating fits tight spaces; overmold defines the outer shape and can add mounting features.
6. Cost and production volume. Heat-shrink is low cost and flexible to change; overmold carries tooling that pays back at volume. Match the method to the build volume and the design's durability requirements.
Common mistakes buyers make
The first mistake is leaving high-current bars bare and trusting the air gap. The Central Europe pack failed this way: vibration narrowed the clearance and the exposed copper arced against the bracket.
The second mistake is putting brittle epoxy on a vibrating bar. The film cracks and lifts at flex points, leaving a bare edge where the crack opened.
The third mistake is sizing insulation only for current. A bar can carry its rated current and still fail insulation-wise if the material's voltage rating, tracking resistance or temperature range is underspecified.
The fourth mistake is covering the joint with insulation. Insulation over a bolted or welded contact interferes with conductivity and service; the contact surface stays exposed and the insulation stops at its edge.
The fifth mistake is skipping a vibration and thermal sample. Insulation that looks fine on the bench can loosen, crack or shift after cycling. A prototype through vibration and temperature confirms the method before production.
What Shanyo supplies and tests
At Shanyo we manufacture copper and aluminum bus bar assemblies with heat-shrink, epoxy-coated or overmolded insulation to the pack's voltage, vibration and temperature requirements. Bars can be punched, bent and plated to the drawing, with joint holes, mounting features and insulation coverage specified on the part. We build prototypes within 48 hours of the drawing freeze and supply wholesale and OEM bus bars for EV, energy storage and industrial power builders.
Shanyo also supplies metal domes, dome sheet arrays, silicone buttons and FPC assemblies from our Qingdao factory. Send us the current and voltage, the vibration and temperature range, the bar geometry, the joint service needs and the enclosure clearance, and our engineering team will recommend the insulation method and quote factory pricing. Contact Shanyo for an insulated bus bar sample.
Insulation materials and ratings
The insulation material carries the dielectric, thermal and mechanical load behind the method. Heat-shrink tubing is commonly a polyolefin, rated to a temperature range and a dielectric strength, with adhesive-lined versions that seal against moisture and movement. Epoxy coatings are resin films selected for adhesion, temperature and chemical resistance on the bar surface. Overmold resins are engineering plastics chosen for impact, temperature, flame rating and the ability to hold a molded shape around the copper. The material grade is matched to the voltage, the pack temperature and any required flame or safety standard, not picked from a generic insulator list.
Copper surface preparation affects how the insulation holds. A clean, degreased bar bonds better than one with oil or oxidation at the interface. Plating on exposed contact areas protects the joint; covered areas rely on the insulation rather than the plating. Where the bar carries high current, the conductor cross-section and the insulation temperature rating are checked together, because heat from the current raises the bar temperature the insulator must survive.
Bar shape, bending and mounting
Bus bars are punched or bent to the pack layout: straight links, bent offsets, profiled branches and drilled joint holes. Heat-shrink follows a simple bend but needs boots or longer sleeves at sharp corners and ends. Epoxy coats the profile but stays thin on edges that flex. Overmold defines the outer contour and can wrap the edges that tubing and coating leave weak. Mounting bosses, locating holes and stand-offs can be molded into the overmold shell, which locates the bar in the pack and keeps the clearance to neighboring metal consistent.
Thermal expansion matters between copper and the insulation. Copper and the polymer expand at different rates, and repeated heating and cooling can loosen a poorly fitted tube or stress a brittle coating. The insulation is sized and bonded to hold through that cycle, and the bar's mounting allows the movement without pinching the insulator against a bracket.
Automotive, storage, industrial and consumer power
In EV packs, bars connect cell modules, modules to the BMS and the pack to the output. Vibration, high voltage and close cell packing push shaped bars toward overmold; lower-voltage static links can use tubing. In energy storage racks, fixed busbars between modules favor heat-shrink or epoxy, with clearance held to the rack. In industrial power distribution, panel and machine bars balance repairability against vibration, using tubing on static panels and overmold on vibrating equipment. In consumer power tools and small battery devices, smaller bars use tubing or thin coating where current and voltage are lower and cost targets are tighter.
Checking insulation before production
Before a bus bar goes to production, we confirm the conductor cross-section against the current and temperature rise, select the insulation material to the voltage and thermal range, and check the coverage at bends, edges and joints. A prototype goes through vibration and thermal cycling to confirm the insulation stays seated and intact, and the joint surfaces stay conductive and accessible. The bar drawing records the conductor material, plating, insulation method, material grade and coverage, so a later reorder keeps the same insulated assembly.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

