A European medical device maker came to us after a batch of silicone keypads started failing on the production line. The keypads used a standard carbon conductive pill on the back of each silicone button, pressing against a carbon-printed PCB pad. At first the contact resistance was fine. By the hundred-thousandth actuation, the resistance on some keys had climbed above 500 ohms, and the controller stopped registering those keys. The customer pulled two thousand units off the line.
We swapped the conductive pill from standard carbon to a silicone-carbon pill, and redesigned the PCB pad as a gold-plated contact. The contact resistance stayed under 100 ohms past one million actuations, and the failures stopped. That project is the subject of this guide. The conductive pill on the back of a silicone button is the part most buyers pick by habit, and it is the part that decides whether the keypad lasts a decade or fails in a year.
This guide compares carbon, gold-plated and silicone-carbon pills on contact resistance, life, cost and application, and maps each to the product it suits.
What the conductive pill does
A silicone keypad is a rubber mat with molded domes. On the underside of each dome sits a small conductive pill. When the operator presses the key, the dome collapses and the pill touches two PCB contact pads, closing the circuit. The pill is the only electrical contact in the keypad. Its material decides the contact resistance, the wear life, and how the keypad ages.
There are three common pill materials. Carbon pill is a carbon-loaded rubber, the cheapest and the default. Gold-plated pill is a metal plunger plated with gold, for low and stable contact resistance. Silicone-carbon pill is a silicone loaded with carbon, softer and more compliant than the hard carbon pill.

The conductive pill on the underside of the silicone dome is the electrical contact. Carbon, gold-plated and silicone-carbon each suit a different life target.
Carbon vs Gold-Plated vs Silicone-Carbon: comparison table
| Parameter | Carbon pill | Gold-plated pill | Silicone-carbon pill |
|---|---|---|---|
| Contact resistance | 100-500 ohm | <50 ohm | 50-200 ohm |
| Life | 100k-500k | 1M+ | 500k-1M |
| PCB pad match | Carbon | Gold or tin | Carbon or gold |
| Compliance | Hard | Hard metal | Soft silicone |
| Relative cost | Lowest | Highest | Moderate |
| Best fit | Low-cost short-life | Medical, long-life | General purpose |
How each pill behaves
Carbon pill is the default. It is a carbon-loaded rubber disc, bonded to the underside of the silicone dome. It presses against a carbon-printed PCB pad. It is cheap, and it works for a low-cost remote or a toy. But the carbon wears: after 100k to 500k actuations, the contact resistance climbs, because the carbon on the pill and the carbon on the pad wear against each other. This was the pill that failed on our medical customer's keypads.
Gold-plated pill is a metal plunger, usually brass or nickel, plated with gold. It presses against a gold or tin PCB pad. The gold gives a contact resistance under 50 ohms that stays stable past one million actuations. It is the most expensive pill, but it is the only choice for a medical device expected to last a decade, or a high-frequency industrial keypad. This was not the pill we chose; we chose the silicone-carbon, because the medical customer did not need gold-level resistance but did need longer life than plain carbon.
Silicone-carbon pill is a silicone rubber loaded with carbon, softer and more compliant than the hard carbon pill. It presses against a carbon or gold pad. The soft silicone conforms to the pad, giving a larger contact area and a more stable resistance than the hard carbon pill. It lasts 500k to 1M actuations, at a moderate cost. This was the pill that fixed our medical customer's failing keypads.

The pill material decides contact resistance and life; the dome below it decides the feel.
Which pill for which product
Consumer remote, toy, short-life device - carbon. A TV remote, a toy or a low-cost calculator that sees 100k actuations or less over its life uses the carbon pill. The carbon is cheapest, and the life is enough. This is the default for consumer products.
Medical device, industrial keypad, long-life product - silicone-carbon. A bedside monitor, an industrial pushbutton panel or a POS terminal that sees 500k to 1M actuations uses the silicone-carbon pill. The soft silicone gives a more stable resistance than the hard carbon, at a moderate cost. This was the fix for our medical customer.
High-frequency industrial, military, gold-contact requirement - gold-plated. A high-frequency industrial keypad, a military panel, or a product that needs contact resistance under 50 ohms past one million actuations uses the gold-plated pill. It is the highest cost, but it is the only pill that holds up at that level.
Low-cost disposable, short life - carbon. A disposable panel, a one-time-use device or a promotional product that sees a few thousand actuations uses the carbon pill. The cost is lowest, and the life is not a constraint.
Selection checklist
1. Target life in actuations. Under 500k, carbon. 500k to 1M, silicone-carbon. Over 1M or under 50 ohms, gold-plated.
2. Required contact resistance. If the controller needs a stable resistance under 50 ohms, gold-plated. If 100-200 ohms is acceptable, silicone-carbon or carbon.
3. PCB pad material. Carbon pill matches a carbon pad. Gold-plated pill matches a gold or tin pad. Silicone-carbon works on either. Match the pill to the pad.
4. Cost target. Carbon is cheapest. Silicone-carbon is moderate. Gold-plated is highest. Match the pill to the product price class.
5. Compliance and dust. The soft silicone-carbon pill conforms to the pad and tolerates a little dust. The hard carbon or gold pill needs a cleaner pad. For a dusty industrial environment, silicone-carbon is the safer choice.
Common selection mistakes
The first mistake is specifying a hard carbon pill for a medical device expected to last a decade. The carbon wears, the resistance climbs, and the keys fail. Our medical customer's batch started exactly this way. For a long-life device, silicone-carbon or gold-plated.
The second mistake is specifying a gold-plated pill for a low-cost TV remote. The gold adds cost the remote does not need. Match the pill to the life target.
The third mistake is mixing a carbon pill with a gold pad, or a gold pill with a carbon pad. The contact chemistry mismatches, and the resistance is unstable. Match the pill material to the pad material.
The fourth mistake is ignoring the compliance. A hard carbon pill on a dusty pad skips the dust and loses contact. A soft silicone-carbon pill conforms and tolerates a little dust. For a dusty environment, silicone-carbon.
What we supply and test
At Shanyo we produce silicone keypads with carbon, gold-plated or silicone-carbon pills, matched to the customer's life target and PCB pad material. Each lot is tested for contact resistance and for resistance after a life cycle, and the test report ships with the order. Prototype keypads ship within 48 hours from a drawing.
Shanyo manufactures custom OEM and wholesale silicone keypads, dome sheet arrays and membrane switches for consumer, medical, automotive and industrial products, with ISO 13485 supporting medical programs and IATF 16949 covering automotive. Send us your target life and your PCB pad material, and our engineering team will recommend the carbon, gold-plated or silicone-carbon pill and quote factory pricing. Contact Shanyo for a sample keypad with your chosen pill and a life-cycle trial.
Cost trade-off, stated plainly
The carbon pill is the cheapest because it is a carbon-loaded rubber disc. The silicone-carbon pill is moderate, a softer silicone loaded with carbon. The gold-plated pill is the highest, because it is a metal plunger plated with gold. On a sixteen-key keypad, the gap between carbon and gold-plated is a fraction of the finished product cost.
The mistake buyers make is reading the pill cost on the quote and specifying carbon everywhere. The correct comparison is the cost of a failed keypad: a medical device pulled from service, a board reworked, and the reputation of a product that should have lasted a decade. On the medical customer's batch, the two thousand pulled units paid for the silicone-carbon pill on thousands of future keypads. For a low-cost toy, carbon is the right economic choice.
Life and contact resistance detail
The pill does not change the key feel; it changes whether the contact stays good. A carbon pill starts at a low resistance, but the carbon wears on carbon, and the resistance climbs as the pads wear. A silicone-carbon pill starts a little higher, but the soft silicone conforms and the resistance stays flatter over the life. A gold-plated pill starts lowest and stays flattest, because gold is a noble metal that does not oxidize.
We test each production lot for contact resistance at start and after the rated life, so the buyer sees the pill confirmed before shipment. The test cycles the key at the rated force, measures the resistance, and confirms it stays within spec. This is the detail that most often gets missed on a first prototype, because the resistance looks fine at 1k actuations and only drifts at 100k.
Sample and trial
For buyers who need a feel before tooling, we ship a sample keypad with the candidate pill, so the customer can measure the contact resistance on their own PCB pad and run a life test. The sample ships free for qualified medical and industrial programs with a defined panel design. Prototype silicone keypads ship within 48 hours from a drawing.
Where each pill is the wrong choice
To make the decision concrete: do not specify a hard carbon pill for a medical bedside monitor expected to last a decade, where the carbon wears and the resistance drifts. Do not specify a gold-plated pill for a low-cost TV remote, where the gold adds cost the remote does not need. Do not mix a carbon pill with a gold pad, where the contact chemistry mismatches. And do not ignore the compliance on a dusty industrial panel, where a hard pill skips the dust and loses contact. These four rules cover the majority of conductive pill mistakes we see returned from the field.
We also supply the pill-matched silicone keypad integrated into a complete FPC dome module or a membrane switch assembly, depending on how the panel is built. Send us your panel drawing and target life, and we will recommend the carbon, gold-plated or silicone-carbon pill within one working day. Buy direct from the factory and get the pill right the first time. Wholesale and OEM orders welcome, and we support volumes from prototype to mass production.
The medical customer's keypads are now shipping with the silicone-carbon pills, and the contact resistance failures have stopped. If you are replacing a carbon-pill keypad that drifts after 100k actuations, send us your target life and a photo of the PCB pad. We will tell you within a day whether silicone-carbon or gold-plated solves it, and ship a sample for the bench.
Pill size and dome geometry
The pill size is matched to the dome and the PCB pad. A pill too small touches only part of the pad and raises the resistance. A pill too large catches on the pad edge and wears. We set the pill diameter to cover the two PCB contact pads with margin, so the contact area is consistent across the dome's travel. The pill height is matched to the dome's collapsed height, so the pill touches the pad at the end of the travel and not before.
For a metal dome switch on a PCB rather than a silicone keypad, the metal dome itself is the contact, and the pill is not used. The pill is specific to silicone rubber keypads, where the rubber dome needs a conductive underside. This guide is for silicone keypad buyers, not for loose metal dome buyers.
Thank you for reading. We look forward to your inquiry.
Best regards, Shanyo.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

