A European medical device maker came to us after a control panel came back from the field. Their bedside monitor used a 12mm round metal dome under each key, and the keys were laid out on a 12mm grid. On a cramped bedside monitor, the 12mm dome overlapped the adjacent key pad, and a press on one key sometimes triggered the neighbor. The customer had already built the enclosure and the overlay, and the fix had to come from the dome size, not the layout.
We swapped the 12mm domes for 6mm four-legged domes on the same PCB pad pattern. The 6mm dome sits on a 7mm to 8mm pad, leaves gap between keys, and the neighbor-triggering stopped. The actuation feel changed, but the customer adjusted the overlay travel to match. That project is the subject of this guide. The dome diameter is the first size a buyer picks, and it decides the key pitch, the actuation force, the travel and the life.
This guide compares 4mm, 6mm, 8mm and 12mm domes on force, travel, life, pad size and application, and maps each to the panel it suits.
What the dome diameter decides
A metal dome is a stamped stainless steel disc that snaps when pressed. The diameter decides how big the dome is, how much force it takes to snap, how far it travels, and how long it lasts. A larger dome covers a bigger pad, travels farther, and takes more force. A smaller dome fits a tighter key pitch, travels less, and takes less force. The diameter is the first number on a dome drawing, before the shape or the plating.
The four common diameters are 4mm, 6mm, 8mm and 12mm. They are round domes, though four-legged and cross shapes also come in these sizes. The 4mm is the smallest standard dome, the 12mm is the largest.

Dome diameter sets the key pitch, actuation force and travel. Pick the size to fit the panel grid, not the other way around.
4mm vs 6mm vs 8mm vs 12mm: comparison table
| Parameter | 4mm dome | 6mm dome | 8mm dome | 12mm dome |
|---|---|---|---|---|
| Typical force | 100-200g | 180-280g | 250-400g | 300-500g |
| Travel | 0.1-0.2mm | 0.2-0.3mm | 0.25-0.4mm | 0.3-0.5mm |
| Pad diameter | 4-5mm | 6-7mm | 8-9mm | 11-13mm |
| Key pitch | 6-8mm | 8-12mm | 12-16mm | 16-22mm |
| Life | 300k-1M | 500k-1M | 500k-2M | 1M-5M |
| Best fit | Dense keypads | General purpose | Industrial | Big buttons, gloves |
How each size behaves
4mm dome is the smallest. It takes 100 to 200 grams to snap, travels about 0.1 to 0.2mm, and fits a tight 6 to 8mm key pitch. It suits a dense keypad on a handheld remote, a calculator, or a small consumer product where the keys must fit close together. The feel is light and shallow, and it is not the dome for gloved operation.
6mm dome is the workhorse. It takes 180 to 280 grams, travels 0.2 to 0.3mm, and fits an 8 to 12mm pitch. It is the dome for a medical panel, an industrial pushbutton, a POS terminal, and the middle of most product lines. This was the size that fixed our medical customer's cramped bedside monitor.
8mm dome is the industrial size. It takes 250 to 400 grams, travels 0.25 to 0.4mm, and fits a 12 to 16mm pitch. It suits a factory floor panel, a heavy machinery control, or a product where the operator wears thin gloves. The feel is firm and the travel is obvious.
12mm dome is the largest. It takes 300 to 500 grams, travels 0.3 to 0.5mm, and fits a 16 to 22mm pitch. It suits a big industrial pushbutton, a gloved outdoor keypad, or a panel where the operator cannot see the key and needs a clear click. It is too big for a dense bedside monitor, which was the mistake on our medical customer's first build.

Four-legged domes come in 4, 6, 8 and 12mm. The four legs sit on the PCB pads.
Which size for which product
Handheld remote, calculator, dense keypad - 4mm. A handheld remote or a calculator with many keys on a small panel uses the 4mm dome. The tight 6 to 8mm pitch fits the keys, and the light feel suits a bare-finger consumer product.
Medical panel, POS, general purpose - 6mm. A bedside monitor, a POS terminal or a general industrial panel uses the 6mm dome. It is the middle of the range, fits an 8 to 12mm pitch, and feels right for bare-finger office and medical use.
Factory floor, thin glove, firm feel - 8mm. A factory panel or a heavy-machine control uses the 8mm dome. The firm force and longer travel read clearly through thin gloves and on a vibrating machine.
Big pushbutton, thick glove, outdoor - 12mm. A gloved outdoor keypad, a big industrial pushbutton or a blind-operated panel uses the 12mm dome. The large click and long travel are felt through thick gloves and without looking.
Selection checklist
1. Key pitch. Measure the center-to-center distance between keys. If the pitch is 6 to 8mm, use 4mm. 8 to 12mm, use 6mm. 12 to 16mm, use 8mm. 16mm and above, use 12mm. The dome must fit the pitch, not the other way around.
2. Actuation force needed. Bare-finger consumer: 100 to 200g. General purpose: 180 to 280g. Industrial firm: 250 to 400g. Gloved: 300 to 500g. Match the dome size to the force, and the force to the operator's glove.
3. Travel needed. A shallow 0.1 to 0.2mm feels like a consumer remote. A deeper 0.3 to 0.5mm feels like an industrial button. Pick the travel the operator expects.
4. Life rating. The larger domes generally last longer, up to 1M to 5M cycles on the 12mm. A consumer remote sees 100k actuations; a factory panel sees millions. Pick the size that meets the life target.
5. PCB pad size. The dome must sit on a pad of matching size. A 12mm dome on a 6mm pad sits on the edge and misfires. Match the pad to the dome before you lay the board.
Common selection mistakes
The first mistake is putting a 12mm dome on a cramped medical panel. The big dome overlaps the neighbor pad and triggers the wrong key. Our medical customer's first build started exactly this way. On a tight grid, go down to 6mm.
The second mistake is putting a 4mm dome on a gloved outdoor keypad. The 100 to 200g force is too light through a glove, and the operator cannot feel the click. For gloves, go up to 8mm or 12mm.
The third mistake is laying the PCB pads first and picking the dome size later. The pads decide the dome size, so pick the dome before you route the board. Swap a dome size after the board is laid means re-spin the PCB.
The fourth mistake is ignoring the pad size. A dome that hangs over the pad edge loses contact and misfires. The pad diameter must match the dome, not just be a similar number.
What we supply and test
At Shanyo we supply 4mm, 6mm, 8mm and 12mm dome sheet arrays, round, four-legged and cross shapes, in stainless steel with silver or carbon plating. Each dome is tested for actuation force to plus or minus 10 grams, and the life is confirmed on a sample before the lot ships. Prototype dome sheets ship within 48 hours from a drawing.
Shanyo manufactures custom OEM and wholesale metal domes, dome sheet arrays and membrane switches for consumer, medical, automotive and industrial panels, with ISO 13485 supporting medical programs and IATF 16949 covering automotive. Send us your key pitch and your actuation force target, and our engineering team will recommend 4mm, 6mm, 8mm or 12mm and quote factory pricing. Contact Shanyo for a sample dome sheet with your chosen size.
Cost trade-off, stated plainly
The 4mm dome is the cheapest because it uses the least stainless steel. The 12mm dome costs more because the stamping is larger and the tooling is bigger. On a dense consumer remote with forty keys, the gap between 4mm and 6mm is small, but the gap between 6mm and 12mm is visible on the BOM. Match the size to the key pitch and the force target, not to the per-dome price.
The mistake buyers make is reading the per-dome price and specifying the 4mm everywhere. The correct comparison is the cost of a cramped panel that triggers the neighbor key, or a gloved keypad the operator cannot feel. On the medical customer's bedside monitor, the swap from 12mm to 6mm cost a PCB re-spin once, and the panel was correct for the product life. For a dense handheld remote, the 4mm is the right economic choice.
Life and force tolerance detail
The larger dome carries a higher life rating because the stainless steel flexes over a larger radius and the stress per cycle is lower. The 12mm dome is rated for 1M to 5M cycles, while the 4mm is rated for 300k to 1M. This is why a factory panel that sees millions of presses uses the 8mm or 12mm, and a consumer remote that sees a few hundred thousand uses the 4mm or 6mm.
The actuation force is controlled to plus or minus 10 grams on each size. We test each lot on a force-displacement gauge and confirm the snap force and the travel before shipment. The tolerance matters: a 200g dome that actually snaps at 250g feels wrong to the operator, and a 6mm dome that snaps at 150g feels mushy. The plus or minus 10g band is what keeps the feel consistent across the production run.
Sample and trial
For buyers who need to feel the dome before tooling, we ship a sample keypad with the candidate size, so the customer can compare the 4mm, 6mm, 8mm and 12mm feel on their own bench. The sample shows the force, the travel and the noise of the snap. Prototype dome sheets ship within 48 hours from a drawing. Wholesale and OEM orders welcome, and we support volumes from prototype to mass production.
Where each size is the wrong choice
To make the decision concrete: do not put a 12mm dome on a cramped medical bedside monitor where the keys are on a 10mm grid, because the big dome overlaps the neighbor pad. Do not put a 4mm dome on a gloved outdoor keypad, because the light 100 to 200g force is not felt through a glove. Do not lay the PCB pads before picking the dome size, because a 12mm dome on a 6mm pad misfires. And do not ignore the plus or minus 10g force tolerance, because a dome that snaps at the wrong weight feels wrong to the operator. These four rules cover the majority of dome size mistakes we see returned from the field.
We also supply the dome size integrated into a complete FPC dome module or a silicone keypad assembly, depending on how the panel is built. Send us your key pitch and your glove condition, and we will recommend 4mm, 6mm, 8mm or 12mm within one working day. Buy direct from the factory and get the dome size right the first time.
The medical customer's bedside monitor is now shipping with the 6mm domes, and the neighbor-key triggering has stopped. If you are laying out a new panel and unsure whether 4mm, 6mm, 8mm or 12mm fits your key pitch, send us the pitch and the force target. We will recommend the size within a day and ship samples for the bench.
Thank you for reading. We look forward to your inquiry. Best regards, Shanyo team.
Dome shape within a size
Within each diameter, the dome comes in round, four-legged and cross shapes. The round dome is the cheapest and gives a circular contact. The four-legged dome gives a stable four-point contact and tolerates a little dust. The cross dome gives the most stable contact and the longest life. The diameter picks the size; the shape picks the contact stability. For a dusty factory, the four-legged or cross 8mm dome is the safer pick than a round 8mm.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

