A European industrial equipment maker came to us with a dome sheet array that was sliding off the PCB. The customer had specified a hot-melt adhesive on the dome sheet, and the control panel sat inside an outdoor cabinet that reached 60°C in summer. The hot-melt softened, the dome sheet shifted a few millimeters, and the domes no longer aligned to the PCB pads. The panel stopped registering half its keys, and twenty boards had to be pulled and reworked.
We swapped the adhesive to an acrylic pressure-sensitive adhesive rated for -40 to 85°C. The acrylic held the dome sheet flat across the temperature range, the alignment came back, and the boards stayed in service. That project is the subject of this guide. The adhesive that holds a dome sheet to the PCB is the part most buyers spec last, and it is the part that fails first in a hot cabinet.
This guide compares acrylic, silicone and hot-melt adhesives for dome sheets on temperature, adhesion, rework and application, and maps each to the product it suits.
What the retention adhesive does
A dome sheet is a polyester carrier that holds the metal domes aligned to the PCB pads. The sheet has a layer of adhesive on the back that sticks it to the PCB or the panel housing. The adhesive keeps the sheet flat, keeps the domes aligned, and survives the product's operating temperature range. There are three common adhesive families.
Acrylic adhesive is a pressure-sensitive acrylic, the most common for dome sheets. It holds across a wide temperature range, cleanly, and reworks with heat. Silicone adhesive is a silicone-based pressure-sensitive, for extreme high or low temperature where acrylic softens. Hot-melt adhesive is a thermoplastic adhesive that melts on application and hardens on cooling, cheap but temperature-limited.

The adhesive layer on the back of the dome sheet holds it to the PCB. Acrylic, silicone and hot-melt each suit a different temperature range.
Acrylic vs Silicone vs Hot-Melt: comparison table
| Parameter | Acrylic PSA | Silicone PSA | Hot-melt |
|---|---|---|---|
| Temperature range | -40 to 85°C | -60 to 200°C | -10 to 50°C |
| Adhesion | High | Medium-high | High when cold |
| Rework | Heat and peel | Harder, high-temp | Heat and peel |
| Relative cost | Low-moderate | Higher | Lowest |
| Aging | Good | Excellent | Poor over years |
| Best fit | Most products | Extreme temp | Cool, dry, low-cost |
How each adhesive behaves
Acrylic PSA is the default. It is a pressure-sensitive acrylic, applied as a dry film on the back of the dome sheet. The operator presses the sheet onto the PCB, and the adhesive bonds. It holds from -40 to 85°C, which covers consumer, medical and most industrial products. It reworks cleanly with a heat gun and a peel. This was the adhesive that fixed our industrial customer's sliding dome sheet.
Silicone PSA is for extreme temperatures. It holds from -60 to 200°C, where acrylic softens and hot-melt melts. It is used under a car hood, in an oven control, or in a cold-storage panel. It costs more than acrylic and is harder to rework, but it is the only adhesive that holds at 200°C.
Hot-melt is the cheapest. It is a thermoplastic adhesive applied hot, and it hardens on cooling. It holds at room temperature, but it softens above 50°C and creeps below -10°C. It is used in low-cost, cool, dry products where temperature is controlled. It was the adhesive that failed on our industrial customer's outdoor cabinet.

The domes are unchanged; the adhesive on the back is what keeps the sheet aligned across the product's temperature range.
Which adhesive for which product
Consumer electronics, office devices, indoor room temperature - acrylic. A TV remote, a printer panel or a home thermostat in a controlled room uses acrylic PSA. The acrylic holds across the room temperature range, reworks cleanly, and costs less than silicone. This is the default for most dome sheets.
Automotive under-hood, oven controls, cold storage - silicone. A panel under a car hood, an oven control or a cold-storage unit sees temperatures above 85°C or below -40°C. The acrylic softens, so the silicone PSA holds. This is the construction for extreme temperature products.
Low-cost toys, indoor disposables, cool dry use - hot-melt. A low-cost toy, a disposable panel or a device that stays in a cool dry room uses hot-melt. The hot-melt is the cheapest, and the temperature range never challenges it. But do not use it on a panel that sees summer heat.
Outdoor cabinets, industrial enclosures, sun-exposed panels - acrylic. A control panel in an outdoor cabinet that reaches 60°C uses acrylic, not hot-melt. The acrylic holds to 85°C, so the summer cabinet temperature stays inside the range. This was the adhesive swap that fixed our customer's sliding dome sheet.
Selection checklist
1. Operating temperature range. If the panel sees -40 to 85°C, acrylic. If above 85°C or below -40°C, silicone. If controlled room temperature, hot-melt is acceptable.
2. Rework requirement. Acrylic reworks cleanly. Silicone reworks harder. Hot-melt reworks but leaves residue. Match the adhesive to the rework plan.
3. Product life. Acrylic ages well over years. Silicone ages best. Hot-melt creeps and dries over years. For a product expected to run for a decade, acrylic or silicone.
4. Cost target. Hot-melt is cheapest. Acrylic is moderate. Silicone is highest. Match the adhesive to the product's price class.
5. Alignment tolerance. If the domes must stay aligned to the pads across temperature, use acrylic or silicone. Hot-melt creeps and shifts.
Common selection mistakes
The first mistake is specifying hot-melt for an outdoor cabinet panel. The industrial customer's sliding dome sheet started exactly this way. The hot-melt softens at 60°C, the sheet shifts, and the domes lose alignment. For an outdoor cabinet, acrylic.
The second mistake is specifying acrylic for an under-hood automotive panel. The acrylic softens above 85°C, and the sheet shifts. Under the hood, silicone.
The third mistake is specifying silicone for a consumer remote where the room temperature never challenges acrylic. The silicone adds cost where the acrylic would do. Match the adhesive to the temperature.
The fourth mistake is ignoring rework. A hot-melt panel that needs rework leaves residue on the PCB. For a product that will be serviced, acrylic.
What we supply and test
At Shanyo we produce dome sheet arrays with acrylic, silicone or hot-melt adhesive, matched to the customer's operating temperature range. Each lot is tested for adhesion and for retention across the temperature range, and the test report ships with the order. Prototype dome sheets ship within 48 hours from a drawing.
Shanyo manufactures custom OEM and wholesale dome sheets and membrane switches for consumer, medical, automotive and industrial products, with ISO 13485 supporting medical programs and IATF 16949 covering automotive. Send us your operating temperature range and rework requirement, and our engineering team will recommend the acrylic, silicone or hot-melt adhesive and quote factory pricing. Contact Shanyo for a sample dome sheet with your chosen adhesive and a temperature-retention trial.
Cost trade-off, stated plainly
Hot-melt is the cheapest adhesive because it is a thermoplastic applied hot. Acrylic is moderate, a dry pressure-sensitive film. Silicone is the highest, because the silicone adhesive is a specialty material. On a sixteen-button dome sheet, the gap between hot-melt and silicone is a fraction of the finished panel cost.
The mistake buyers make is reading the adhesive cost on the quote and specifying hot-melt everywhere. The correct comparison is the cost of a sliding dome sheet: a panel pulled from service, a board reworked, and the domes out of alignment. On the industrial customer's run, the rework on twenty boards paid for the acrylic adhesive on thousands of future sheets. For a low-cost toy in a cool dry room, hot-melt is the right economic choice.
There is also a service consideration. An acrylic dome sheet lets a technician peel the sheet with heat and re-stick it, leaving no residue. A hot-melt sheet leaves a gummy residue that the PCB must be cleaned before re-sticking. For a product serviced in the field, the acrylic is the cheaper choice over the product life, even if the per-piece adhesive cost is higher on the quote.
What we ask for before recommending an adhesive
To recommend acrylic, silicone or hot-melt, we need three inputs: the product's operating temperature range, whether the panel will be reworked or serviced, and the product life expected. With those three numbers we can rule out the wrong adhesive immediately. Missing the temperature input is the most common reason a first dome sheet comes back sliding, because the buyer specified hot-melt for an outdoor cabinet without telling us about the summer heat.
Life and field reliability
The adhesive does not change the dome feel or the switch life; it changes how the sheet stays on the PCB. An acrylic PSA stays flat and aligned across the product life, and the adhesion holds because the adhesive is a dry film that does not creep. For a product expected to run for years, the acrylic or silicone is the cheaper choice over the product life, even if the per-piece cost is higher on the quote.
Adhesive test and temperature detail
Beyond the adhesive family, we test each production lot for adhesion and retention across the customer's operating range. The adhesion test measures peel force on the PCB material. The retention test cycles the dome sheet through the temperature range and confirms the domes stay aligned to the pads. The test report ships with the order, so the buyer sees the adhesive confirmed before shipment.
The adhesive is applied to the polyester carrier at the right thickness, so the sheet sits flat on the PCB without a bump. The thickness of the adhesive layer matters; too thick and the dome sits off the pad, too thin and the adhesion drops. We match the adhesive thickness to the dome height and the PCB standoff, so the dome clicks at the rated force. This is the detail that most often gets missed on a first prototype.
Sample and trial
For buyers who need a feel before tooling, we ship a sample dome sheet with the candidate adhesive, so the customer can stick it to their PCB, cycle it through the temperature range, and confirm the domes stay aligned. The sample ships free for qualified industrial and automotive programs with a defined panel design.
Where each adhesive is the wrong choice
To make the decision concrete: do not specify hot-melt for an outdoor cabinet panel, where the summer heat softens the adhesive and slides the sheet. Do not specify acrylic for an under-hood automotive panel, where the engine heat softens the acrylic. Do not specify silicone for a consumer remote, where the silicone adds cost and rework difficulty for a room-temperature product. And do not specify a thin adhesive layer that leaves the dome off the pad, where the click feels wrong. These four rules cover the majority of dome sheet adhesive mistakes we see returned from the field.
We also supply the adhesive-matched dome sheet integrated into a complete silicone button assembly or a FPC dome module, depending on how the panel is built. Send us your panel drawing and operating temperature range, and we will recommend the acrylic, silicone or hot-melt adhesive within one working day. Prototype dome sheets ship within 48 hours from your drawing. Wholesale and OEM orders welcome, and we support volumes from prototype to mass production. Buy direct from the factory and get the adhesive right the first time.
The industrial customer's outdoor cabinets are still in service, six months after the acrylic adhesive swap. The dome sheets stay aligned through the summer heat, and the rework calls stopped. We look forward to your project.
If you are replacing a sliding dome sheet on an outdoor cabinet, an under-hood panel or a hot industrial enclosure, send us your operating temperature range and a photo of the current adhesive. We will tell you within a day whether acrylic, silicone or hot-melt solves it, and ship a sample for the bench.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

