A handheld test instrument came back from a field repair with several open pads on its flexible printed circuit. The assembly had sat on the shelf for several months before rework, and the copper pads had oxidized. When the board went to the rework station, solder would not wet the pads; the joints opened instead of forming. The flex layout and traces were sound. The surface finish on the pads had not been chosen for the shelf life, rework and contact condition the board actually saw, and the bare copper oxidized in between.
That case frames this guide. The copper traces and pads of an FPC are covered by a surface finish that keeps the pad solderable or contact-ready until assembly, and protects the exposed copper from oxidation and wear. Four finishes are common on flex circuits: ENIG (electroless nickel immersion gold), OSP (organic solderability preservative), immersion tin, and gold plating in soft or hard form. This guide compares them on solderability, contact wear, shelf life, bond strength and cost, and maps each to automotive, medical, industrial and consumer flex designs.
The finish applies to the exposed pads; the rest of the flex is protected by coverlay or insulation. Where the FPC carries a metal dome or dome sheet array, the contact pad under the dome needs a finish that holds contact resistance over cycles, separate from the pads that will later be soldered.
What the surface finish does
Copper oxidizes in air, and an oxidized pad does not solder well or keep a stable contact. The finish coats the exposed copper pads, prevents oxidation during shelf life and storage, and provides a surface that solder wets or a contact slides on. It also affects how long the pad survives repeated contact, how the bond to a component or connector holds, and how the board performs after rework or a long shelf period. The finish is chosen for the pad's role: solder pads that connect to components, contact pads that interface with a dome or connector, and bond pads for wire bonding each favor a different finish.
On an FPC the finish also meets a flexible base. The coating must stay bonded as the flex bends, and it should not crack or peel under repeated motion. Shelf life matters because flex circuits may be stored before assembly, and a finish that oxidizes quickly limits the usable storage window. Cost varies widely between finishes, so the finish is matched to the electrical and contact requirement rather than applied uniformly to every pad.

Exposed FPC pads carry the surface finish: it keeps copper solderable or contact-ready through storage, assembly and repeated contact, and it is chosen per pad role.
Comparison: ENIG vs OSP vs immersion tin vs gold plating
| Parameter | ENIG | OSP | Immersion tin | Gold plating |
|---|---|---|---|---|
| Finish layer | Nickel under gold | Organic coating | Tin immersion on copper | Soft or hard gold over nickel |
| Solderability | Good, flat pad, rework tolerant | Good fresh, limited shelf life | Good, solderable, tin whisker watch | Soft gold solderable; hard gold for contact |
| Contact wear | Good for light contact | Not for sliding contact | Not for repeated contact | Best for repeated contact and connectors |
| Shelf life | Long | Short, coating degrades | Moderate | Long |
| Flatness / fine pitch | Flat, fine-pitch friendly | Thin, fine-pitch friendly | Can roughen, limited fine pitch | Flat where plated well |
| Relative cost | Moderate to high | Lowest | Moderate | Highest, gold weight dependent |
| Best fit | Mixed solder and contact pads | Low-cost solder pads, short shelf | Solder pads, wave/reflow assembly | Connector contacts, dome pads, bond pads |

A dome or connector rides on the contact pad: that pad needs a wear-resistant finish, while nearby solder pads can use a lower-cost finish matched to soldering.
How each finish behaves
ENIG deposits a nickel layer over the copper, then a thin immersion gold over the nickel. The nickel protects the copper and gives a sturdy pad; the gold keeps the surface solderable and contact-ready until assembly. ENIG gives a flat pad that suits fine pitch and holds up to rework and moderate shelf life. It works for pads that are soldered and for light-contact pads, though the thin gold is not built for heavy repeated sliding. Its cost sits above OSP and tin, driven by the nickel and gold layers.
OSP applies a thin organic preservative film over the copper. It is the lowest-cost finish, leaves a thin flat pad good for fine pitch, and keeps solderability while fresh. Its limits are shelf life and contact: the organic coating degrades with time, humidity and heat, so the board should be assembled soon after fabrication, and OSP is not meant for sliding or repeated contact. It suits low-cost solder pads on boards with short storage and no contact function.
Immersion tin coats the copper with a thin tin layer that keeps the pad solderable. It is solder-friendly for reflow and wave assembly and costs below ENIG. Its limits are fine pitch and contact: the tin surface can roughen, and tin whisker growth is watched on certain designs, and tin is not a repeated-contact finish. It suits solder pads in volume assembly rather than connector or dome contact surfaces.
Gold plating comes as soft gold or hard gold over a nickel underlayer. Soft gold is solderable and used on bond pads and selected solder pads; hard gold is wear-resistant and built for repeated contact, connector fingers and dome pads that cycle many times. It is the most expensive finish, cost tied to the gold thickness and plating area, and it is applied where contact wear or bonding justifies the gold rather than across every pad.
Which finish for which application
Automotive and EV-related flex. Cabin and sensor flexes that see temperature cycling, long service life and possible rework favor ENIG for solder pads; connector and contact fingers use hard gold. Vibration and long service push away from short-shelf-life OSP, and the finish is held to the automotive quality record alongside the rest of the flex stack-up.
Medical devices. Handheld instruments and patient interfaces need stable contact and reliable soldering over a long device life. ENIG covers mixed solder and light-contact pads; hard gold serves connector and dome contact surfaces that cycle repeatedly. Shelf life and rework tolerance matter on devices that may be built in batches and stored before assembly.
Industrial panels and machine flex. Control panels, pendants and station flexes connect to connectors and buttons; contact fingers under repeated actuation use hard gold, while the component solder pads use ENIG or tin depending on assembly and cost. Harsh ambient temperature and cleaning conditions are checked against the finish shelf life.
Consumer electronics. Remotes, small handhelds and low-cost keypads favor OSP or immersion tin on solder pads where cost and short shelf life fit; contact pads under a dome still go to gold or ENIG for a stable contact. Hard gold is reserved for the contact function that needs it, not spread across the whole flex.
Solder pads, contact pads and bond pads
An FPC often mixes pad roles on one board. Solder pads connect to components, shields or connectors by soldering, and need a solderable finish that wets reliably. Contact pads sit under a dome, pill or connector and carry a sliding or pressing contact, needing a finish that holds contact resistance and resists wear. Bond pads for wire or TAB bonding need a gold surface compatible with the bonding process. The finish is assigned per pad role rather than one finish for the whole board; a contact pad on OSP or tin fails in cycles, while a solder pad plated in hard gold adds unnecessary cost.
Selection checklist
1. Pad role: solder, contact or bond. Solder pads need a solderable finish; contact pads need a wear-resistant finish; bond pads need a bonding-compatible gold surface. Assign the finish to each role first.
2. Shelf life before assembly. A board stored for months or in humid conditions needs a long-life finish such as ENIG or gold; OSP suits short storage before assembly.
3. Contact cycles and wear. Pads under repeated dome actuation or connector cycling use hard gold; light occasional contact can take ENIG. OSP and tin are not sliding-contact finishes.
4. Fine pitch and pad flatness. Dense fine-pitch pads favor a flat, thin finish such as ENIG or OSP; rougher finishes limit the minimum pad and space.
5. Rework and repair tolerance. Boards likely to be reworked favor a finish that survives a second heat cycle, such as ENIG, over a coating that degrades on reflow.
6. Cost and gold weight. Gold plating cost rises with gold thickness and area; use hard gold only on the contact pads that need it, and keep solder pads on a lower-cost finish.
Common selection mistakes
The first mistake is leaving pads without a matched finish and letting copper oxidize. The handheld FPC failed this way: oxidized pads would not solder after storage, and the joints opened.
The second mistake is putting OSP or tin on a contact pad. These finishes protect solderability but wear through under repeated dome or connector contact, and contact resistance drifts as the coating wears.
The third mistake is plating hard gold across every pad. It protects the board but adds gold cost where solder pads only need a solderable finish; the contact function gets the gold, the rest does not.
The fourth mistake is ignoring shelf life and humidity. OSP degrades with time and ambient; a board that waits months for assembly needs a finish that holds through that storage.
The fifth mistake is skipping solderability and contact checks on the sample. A finish that looks plated well may not wet solder or hold contact resistance after cycling. A prototype through assembly and contact cycles confirms the choice before production.
What Shanyo supplies and tests
At Shanyo we build flexible printed circuits with ENIG, OSP, immersion tin and soft or hard gold finish, assigned per pad role to the board's soldering, contact and bonding requirements. The FPC can integrate dome arrays, connector tails, stiffeners and silicone button interfaces to the panel design. We check solderability, contact resistance and shelf conditions on prototypes before production, and sample flexes ship within 48 hours of the drawing freeze.
Shanyo manufactures OEM and wholesale FPCs, dome arrays, membrane switches and silicone keypads for automotive, medical, industrial and consumer builders. Send us the pad roles, the contact cycles, the shelf and storage conditions, the pitch and the assembly or rework plan, and our engineering team will recommend the surface finish and quote factory pricing. Contact Shanyo for an FPC sample.
Nickel underlayer, gold thickness and plating control
On ENIG and gold-plated pads, the nickel underlayer separates the gold from the copper and prevents copper diffusion into the contact surface. Nickel thickness and coverage affect how well the pad resists corrosion and how stable the contact stays over cycles. The gold layer on ENIG is thin, enough to keep the nickel protected and solderable; hard gold plating for contacts is thicker and alloyed for wear, measured by gold thickness and plating area. Under-plating or uneven coverage leaves weak spots where copper shows through, while over-thick gold adds cost without benefit. The plating spec records nickel and gold thickness per pad type.
On a flex circuit, plating follows the flexible base and must stay bonded through bend motion. A finish that cracks or lifts at a bend exposes the copper underneath; the plating process and the coverlay edge are checked so the coated pad stays intact where the flex moves. Pad design around plated features keeps the finish on the contact area and leaves coverlay over the non-pad copper.
Solder wetting, intermetallic and rework
A solderable finish wets the solder so the joint forms a sound intermetallic bond. Oxidized or degraded finish leaves a dull, weak joint that cracks under vibration or thermal cycling. ENIG and tin wet reliably when fresh; OSP protects the copper until the solder melts and the organic film burns off. Rework adds a second heat cycle: some finishes hold up to another reflow, while an OSP coating may have degraded after the first pass. The number of allowed rework cycles is set against the finish, and the assembly process confirms the joint after each pass.
Contact pads do not solder; they carry electrical contact through a dome or connector. Here the finish must keep low, stable contact resistance as the contact presses and slides. Gold resists oxidation and wear, which is why contact surfaces favor gold; nickel under the gold prevents copper from migrating to the contact face. Tin and OSP contact surfaces tarnish and wear, so they are kept off the contact function.
Reliability, shelf life and storage
Shelf life depends on the finish and the storage environment. Organic and tin finishes are more sensitive to humidity, heat and time than nickel-gold finishes. Boards stored in dry packaging and assembled soon after fabrication hold the shorter-life finishes; boards built in batches or held in warm, humid conditions favor ENIG or gold. Moisture and oxidation before assembly show up as weak solder joints or high contact resistance later, so the storage window and packaging are part of the finish decision.
Checking the finish before production
Before an FPC goes to production, we confirm the finish per pad role, check nickel and gold thickness where plated, and run solderability and contact-resistance checks on the prototype. The board is held through the expected storage condition before assembly to confirm the finish still performs, and contact pads are cycled to the expected actuation count. The drawing records the finish type, layer thicknesses, pad roles and the tests passed, so a later reorder keeps the same plated flex circuit.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

