A handheld diagnostic device came back to us after a field batch ran warm. Its FPC routed the main supply and several sensor signals on a light 18μm copper foil. Under the current the supply traces heated up, trace resistance drifted with temperature, and a few units showed voltage sag at the sensor contacts. The flex layout and connector were fine; the copper foil had been chosen for flexibility without checking the current it had to carry. We redesigned the affected power traces to a heavier foil and kept the signal runs on the thin copper, and the drift went away.
That project is the subject of this guide. Flexible printed circuits use copper foil bonded to a polyimide base, and the foil thickness sets how much current a trace can carry, how narrow a line can be etched, how flexibly the FPC bends, and what the panel costs. Common FPC copper weights run 18μm (0.5 oz), 35μm (1 oz) and 70μm (2 oz). This guide compares them on current capacity, flexibility, line width, cost and application, and maps each foil to automotive, medical, industrial and consumer panels.
The FPC often sits under a membrane switch or carries a dome sheet array, so the foil choice interacts with the contacts and the bend radius the flex must survive. Before choosing a copper weight, read the current the traces carry and the flex life the assembly needs.
What copper thickness controls in an FPC
Copper carries current in the trace cross-section. A thicker foil gives a wider, taller conductor for the same line width, so it holds more current at a lower temperature rise and resists voltage drop. A thinner foil bends more easily, supports finer line widths and pitches, and keeps the FPC light and flexible. The trade runs both ways: heavy copper costs more, is stiffer and needs wider minimum traces; light copper flexes better but limits current and heat capacity.
The foil weight also affects etching. A thicker copper layer etches with wider minimum line and space, so dense fine-pitch routing is harder to hold on 70μm foil. The flex life under repeated bending favors the thinner, more ductile foil; heavy copper cracks sooner at a tight bend radius. These limits are checked together when the FPC is laid out, not after the panel is built.

The FPC routes power and signals under the panel: the copper foil sets current capacity, trace width and how flexibly the circuit bends.
Comparison: 18μm vs 35μm vs 70μm FPC copper
| Parameter | 18μm (0.5 oz) copper | 35μm (1 oz) copper | 70μm (2 oz) copper |
|---|---|---|---|
| Current capacity | Low, signal and low-power runs | Moderate, general power and signal | High, main power and high-current traces |
| Flexibility / bend life | Best, thinnest and most ductile | Good, balanced | Lower, stiffer, tighter bend limits |
| Minimum line width | Finest pitch possible | Moderate line and space | Wider minimum traces |
| Temperature rise | Higher under load | Moderate | Lowest for the same current |
| Relative cost | Lowest | Moderate | Highest |
| Best fit | Signal routing, dense fine pitch, flexing tails | General-purpose panels, mixed signal and power | Power distribution, battery and charger lines |
| Limitation | Current and heat limited | No extreme edge | Stiff, coarse lines, higher cost |

The FPC carries the contacts and domes; the foil weight must hold the current while the tail bends through the assembly's motion.
How each foil weight behaves
18μm copper is the lightest common FPC foil. It bends most easily, survives repeated flexing best, and supports the finest line widths and pitches for dense signal routing. Its limit is current: thin traces heat up under load, resistance drifts with temperature, and voltage drop grows on longer supply runs. It suits signal lines, sensor connections, low-power tails and flexing sections where current is small and bend life matters most.
35μm copper is the general-purpose weight. It holds moderate current for mixed signal and power routing, keeps enough flexibility for most panel tails, and etches to a workable line and space. This is the default for most handheld devices, instrument panels and consumer assemblies that carry a mix of signals and modest supply current. It does not give the highest current rating, but it balances capacity, flex and cost for the widest range of designs.
70μm copper is the heaviest of the three. It carries the highest current at the lowest temperature rise and voltage drop, and it handles main power, battery and charger lines where the 35μm foil would run warm. Its limitations are stiffness, cost and trace width: heavy copper is less flexible, needs wider minimum lines, and cracks sooner at a tight bend radius. It is reserved for power traces rather than the whole flex.
Which foil for which application
Automotive and EV-related panels. Cabin controls and sensor tails that bend and carry low current use 18μm or 35μm. Power distribution near battery or charger circuits, where current and temperature rise matter, uses 70μm on the supply traces, often mixed with lighter foil on the signal runs. Vibration and temperature cycling are reviewed with the foil and stiffener together.
Medical devices. Handheld diagnostics, patient keypads and portable instruments carry mostly signal and low-power current, so 18μm or 35μm is typical. Where a device draws higher supply current or sits near a battery, the power traces step up to 35μm or 70μm. Flexing tails on a movable probe or handle favor the lighter foil for bend life.
Industrial panels. Consoles, station controls and machine interfaces route mixed signal and power; 35μm covers most of these. High-current connections to motors, heaters or power modules use 70μm on those traces. A panel that sees harsh ambient temperature keeps temperature rise and trace rating in the margin rather than at the limit.
Consumer electronics. Small handhelds, remote controls, wearables and compact keypads use 18μm for fine pitch and flexibility, with 35μm where a supply rail carries real current. Cost and bend life drive the choice here; high-current 70μm foil is uncommon in low-power consumer products.
Mixed foil on one flex
An FPC does not have to use one foil weight across the whole board. The diagnostic device that came back warm kept 18μm on its sensor signal runs and moved only the affected supply traces to heavier foil. Mixed-weight designs route power lines on the heavier copper and signal lines on the light copper, which balances current capacity against flex and cost. When a design has both high-current and fine-pitch sections, the layout team reviews the foil split before the stack-up is locked.
Selection checklist
1. Current each trace must carry. List the maximum current and the allowable temperature rise for supply and signal lines. High-current traces move up in foil weight; signal lines can stay light. The current calculation precedes the layout.
2. Flex life and bend radius. Sections that bend repeatedly, move on a hinge or run through a sliding part favor 18μm. Heavy copper on a tight, repeated bend cracks sooner; keep power traces on the non-flexing sections where possible.
3. Line width and pitch needed. Dense routing with fine traces and narrow spaces favors light foil. Confirm the minimum trace and space the chosen copper can etch before committing the board layout.
4. Voltage drop and length. Long supply runs lose voltage on thin copper. Check resistance and drop across the run length, not just the current rating at the trace itself.
5. Ambient temperature and enclosure. A sealed or warm enclosure leaves less margin for trace heating; keep the heavier foil and a temperature margin rather than rating a thin trace at its limit.
6. Cost target. Heavier foil and wider traces raise material and processing cost. Use 70μm where the current demands it, not across the whole flex by default.
Common selection mistakes
The first mistake is choosing the lightest foil for flexibility without checking current. The warm handheld FPC failed this way: 18μm traces could not hold the supply current, and resistance drifted with temperature.
The second mistake is putting heavy copper on every trace for assumed margin. 70μm across a fine-pitch flex stiffens the board, forces wider lines and raises cost, and can shorten flex life where the board bends.
The third mistake is ignoring bend radius. Heavy copper under repeated bending fatigues and cracks; a power trace that must flex belongs on a lighter foil, or routed to a non-moving section.
The fourth mistake is rating the trace only for steady current. Inrush, motor start-up and battery charge pulses push peak current above the steady figure; the foil must hold the peak, not just the average.
The fifth mistake is skipping a thermal check on the sample. Current capacity reads differently inside a sealed enclosure than on a bench. A prototype loaded to real current confirms the temperature rise before production.
What Shanyo supplies and tests
At Shanyo we build flexible printed circuits in 18μm, 35μm and 70μm copper, with mixed-weight stack-ups where power and signal sections differ. The FPC can integrate metal domes, a dome array, connector tails and stiffeners to the panel design. We check current capacity, trace width and bend life on prototypes before production, and sample FPCs ship within 48 hours of the drawing freeze.
Shanyo manufactures OEM and wholesale FPCs, dome arrays, membrane switches and silicone keypads for automotive, medical, industrial and consumer builders. Send us the trace currents, the flex motion and bend radius, the ambient temperature and the line pitch, and our engineering team will recommend 18μm, 35μm or 70μm copper and quote factory pricing. Contact Shanyo for an FPC sample.
Copper type, etching and stack-up
FPC copper comes as rolled annealed (RA) or electrodeposited (ED) foil. RA copper is more ductile and bends better, favored on flexing tails and repeated-motion sections. ED copper is common on general rigid-flex and static circuits at lower cost. The foil weight and the copper type are chosen together: a heavy RA foil still bends better than a heavy ED foil, but neither removes the stiffness that thickness brings. For a flexing section, the ductile foil and the lighter weight both matter.
Etching a thicker copper layer requires wider minimum line and space, because the etchant must reach through more metal to clear the gap. Dense fine-pitch boards therefore favor 18μm or 35μm; 70μm traces are laid out wider and spaced further apart. The stiffener and coverlay also change with the foil: heavier copper may need more support under high-current pads, and the coverlay opening around pads is sized to the trace.
Heat, resistance and voltage drop
Current in a trace heats the copper, and resistance rises with temperature. A thin trace carrying near its rating runs hot, drifts resistance, and sags voltage on the way to the load. The heavier foil spreads the same current over a larger cross-section, keeping the trace cooler and the resistance stable. Voltage drop accumulates along the run: a long thin supply line can lose more voltage than the load tolerates even when the short trace looks rated. Both the temperature rise and the drop are checked against the actual run length and the enclosure temperature.
Peak current matters as much as steady current. Motor start-up, sensor wake-up, battery charging and backlight inrush push current above the average for short pulses. A foil sized only for the steady figure can heat through those peaks. The design review lists the peak current and its duration, not just the continuous draw.
How the foil pairs with domes and contacts
On a keypad or switch FPC, the copper under the dome or carbon pill carries the contact signal, usually low current and well served by light foil. The supply and connector lines nearby may need heavier copper. The contact pad itself is plated for contact resistance and wear, separate from the foil weight that carries current. When the FPC integrates a dome array, the routing around each dome keeps fine pitch and light foil, while any power rail on the same flex steps up to the weight the current needs.
Checking the foil before production
Before an FPC goes to production, we lay out the trace currents against the chosen foil weight, confirm the minimum line and space the etching process holds, and check the bend radius and flex life on the moving sections. A prototype is loaded to real current to read the temperature rise in the actual enclosure, and the foil weight, copper type and stiffener are recorded on the drawing so a later reorder keeps the same stack-up.
- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

