Shanyo Launches IP67 Sealed Metal Dome Arrays For Outdoor Solar Trackers

Nov 10, 2026

Leave a message

John Smith
John Smith
Specializing in metal dome array technology, I work as an engineer at Qingdao Shanyo Precision Electronic Technology Co., Ltd. With over 5 years of experience, I focus on developing innovative solutions for mobile device components. Follow me to explore the latest advancements in precision electronics!

A European solar tracker manufacturer came to us after a field failure in southern Spain. Their tracker control boxes used an open metal dome sheet array on the control PCB, behind a membrane keypad with no sealing gasket. During the rainy season, condensation and rainwater worked into the control box, pooled on the PCB, and oxidized the dome contacts. Within two years, about eight percent of the trackers in the field had keys that failed to register. The customer had to send technicians out to swap control boxes at heights of three meters. A service call cost more than the control box itself.

We redesigned the keypad as an IP67 sealed dome sheet array. The dome sheet is bonded to the PCB with a perimeter seal, the membrane overlay is gasketed to the enclosure, and the tail exits through a sealed strain relief. The contacts never see rain or condensation. The customer ran a 72-hour water-immersion test, then a salt-fog cycle, and approved the design for their next tracker generation. This product launch is the subject of this update.

It also answers a question we get from buyers building outdoor control boxes: when does an open dome array work, and when do you need a sealed, IP67 construction?

What changed in the keypad

The original keypad was a standard metal dome sheet on a bare PCB, covered by a membrane overlay that was taped down but not gasketed. It worked in an air-conditioned cabinet. On a solar tracker, the control box sits outside, sees sun, rain, dew and condensation, and the open dome sheet was never designed for that.

The sealed version changes three things. First, the dome sheet array is perimeter-bonded to the PCB, so no moisture can reach the domes from the board side. Second, the membrane overlay is gasketed to the enclosure with a continuous silicone gasket, so the face of the keypad seals to IP67. Third, the FPC tail exits through a sealed cable gland, not an open slot. The operator presses the keys from outside the sealed box, and the electronics inside stay dry.

Sealed dome sheet array
The perimeter seal and gasketed overlay keep rain and condensation off the dome contacts.

Open vs sealed: what differs

The two keypads share the same metal domes, the same actuation feel, and the same PCB layout. The differences are in the sealing layers around the domes.

Open dome array is the standard sheet on a bare PCB, cheapest, and works in a dry cabinet. Perimeter-sealed dome sheet adds a seal around the dome area, keeping board-side moisture out. Gasketed overlay adds a silicone gasket between the membrane face and the enclosure, sealing the front. Sealed tail routes the FPC through a gland, not an open slot. The sealed keypad costs more than the open one, but it solves the rain-failure that no open dome array can survive.

Metal domes
The domes inside the sealed array are unchanged; the sealing layer keeps the contacts dry.

Who this suits

This sealed dome array suits outdoor control boxes, solar trackers, weather stations, outdoor kiosks, agricultural equipment and any panel exposed to rain, dew or condensation. It does not suit an air-conditioned office calculator, a consumer remote used indoors, or a low-cost indoor toy, where the open array is cheaper and the environment is dry.

For the solar tracker builder, the sealed array removed the rain-failure service calls. For a buyer choosing between the two, the rule is simple: if the box is indoors and dry, open; if the box is outdoors or sees condensation, sealed to IP67.

What we supplied

Shanyo manufactured the IP67 sealed dome sheet arrays to the customer's drawing, with the perimeter bond, the gasketed membrane overlay and the sealed FPC tail. The arrays integrate with the customer's tracker control PCB. Prototype samples shipped within 48 hours of the drawing freeze, and production volumes follow.

Shanyo is a custom OEM and wholesale membrane switch and dome sheet array manufacturer in Qingdao, supplying outdoor, industrial and renewable-energy panel builders worldwide. Send us your control box drawing and the outdoor exposure rating you need, and our engineering team will recommend open or sealed construction and quote factory pricing. Contact Shanyo for a sample sealed dome array.

How the IP67 seal is built

The seal works on three sides of the keypad. On the board side, the dome sheet array is bonded to the PCB with a perimeter adhesive that runs around the entire dome area, so moisture cannot creep under the sheet from the board. On the front side, the membrane overlay carries a continuous silicone gasket that compresses against the enclosure flange when the screws are tightened, giving the IP67 front seal. On the tail side, the FPC exits through a sealed cable gland or a gland-style connector, so the wire pass-through does not become the leak point.

The metal domes inside the sealed area are unchanged. They are stainless steel snap domes, typically four-legged, with the same actuation force and travel as the open array. The operator cannot feel the seal from the outside; the click and the key travel are the same. The seal is an extra layer around the domes, not a change to the dome feel.

Open vs perimeter-sealed vs fully gasketed: comparison

Parameter Open dome array Perimeter-sealed IP67 fully gasketed
Front seal None None IP67 gasket
Board-side seal None Perimeter bond Perimeter bond
Tail seal Open slot Open slot Sealed gland
Rain resistance Poor Moderate IP67
Relative cost Lowest Moderate Highest
Best fit Dry indoor Dust and humidity Rain and immersion

Selection checklist

1. Environment. Indoor and dry: open. Indoor with humidity or dust: perimeter-sealed. Outdoor with rain, dew or condensation: IP67 fully gasketed.

2. IP rating needed. If the enclosure already carries an IP rating, the keypad must match it. A sealed box with an open keypad slot leaks. Match the keypad seal to the enclosure rating.

3. Condensation. Even without rain, a box that heats in the sun and cools at night generates condensation. The perimeter seal protects the domes from this. For outdoor boxes, treat condensation as a rain event.

4. Cost target. Open is cheapest. The IP67 fully gasketed is the most expensive. Match the seal to the environment, not to the unit price alone. A field service call costs more than the seal.

5. Serviceability. A fully gasketed keypad is harder to open for repair. If the box needs field service, design the gland and gasket to be re-sealed after opening.

Common mistakes

The first mistake is specifying an open dome array for an outdoor control box. It looks fine on the bench in a dry office and fails in the first rainy season. The solar tracker customer's field failure started exactly this way.

The second mistake is sealing the front face but leaving the tail exit open. The cable pass-through becomes the leak point, and the IP67 rating is only on paper. Seal the tail with a gland.

The third mistake is forgetting the gasket compression. A gasket that is not compressed evenly around the flange leaks at one corner. Use screws on a bolt circle and the right gasket thickness.

The fourth mistake is specifying an IP67 sealed keypad for an indoor office calculator. The gasket and gland add cost the indoor product does not need.

Cost trade-off, stated plainly

The sealed keypad costs more than the open one because of the perimeter bond, the silicone gasket, the sealed gland and the extra assembly steps. On a solar tracker control box, the seal adds a small per-unit cost, but it removes the field service call that the open keypad was generating. The tracker customer calculated that a single truck roll to swap a control box at three meters of height cost more than the seal on a year of trackers. For an indoor calculator, the seal is not worth the cost.

The right comparison is not the keypad unit price. It is the cost of a failed box in the field: a technician truck roll, a swap, and the downtime of a tracker that should have been generating power for twenty-five years. On that math, the IP67 seal pays for itself in the first avoided service call.

Life and environmental testing

The seal does not change the dome life. The stainless steel domes inside still carry the same actuation force and the same cycle rating. The seal protects the contacts, so the domes do not see the oxidation that rain would cause. We test the sealed keypad to IP67 water immersion, then a salt-fog cycle, then a temperature-humidity cycle, and confirm the contact resistance stays within spec after each test.

For solar trackers, the keypad also sees UV and wide temperature swings. The membrane overlay uses a UV-stable polyester, and the silicone gasket stays flexible from minus forty to eighty-five Celsius. The tracker customer ran the sealed samples through a summer in Spain before approving production.

Sample and trial

For builders of outdoor control boxes, we ship a sample sealed keypad so the customer can run the water-immersion test on their own enclosure. The sample shows the gasket compression, the gland exit and the dome feel before tooling. Prototype sealed dome arrays ship within 48 hours from a drawing. Wholesale and OEM orders welcome, and we support volumes from prototype to production.

What we ask for before recommending a keypad

To recommend open or sealed, we need two inputs: the environment the control box lives in, and the IP rating the enclosure must meet. If the box is indoors and dry, open. If the box is outdoors or sees condensation, sealed to match the enclosure rating. With those two numbers we can rule out the wrong construction immediately. Missing the environment input is the most common reason a first keypad comes back with a rain-failure complaint.

The solar tracker customer's next-generation trackers are now shipping with the sealed dome arrays, and the rain-failure service calls have stopped. If you are building an outdoor control box, a weather station, an agricultural enclosure or a solar tracker, send us the drawing and the IP rating, and we will recommend the open or sealed construction within one working day.

We also supply the sealed dome array integrated with a complete FPC tail assembly or a silicone keypad, depending on how the box is built. Buy direct from the factory and get the seal right the first time. We look forward to your outdoor project.

Gasket material and UV exposure

The gasket is silicone, not rubber. Silicone stays flexible from minus forty to eighty-five Celsius, resists UV and does not harden in a sunlit box. A rubber gasket hardens and cracks after a few summers outdoors, and the seal leaks. For an outdoor box, specify the silicone gasket. We also offer a fluorosilicone gasket for boxes that see fuel or oils, such as agricultural equipment. For a solar tracker in clean air, the standard silicone is enough.

If you are replacing an open dome array on an outdoor box and seeing contact failures after rain, send us a photo of the enclosure and the IP rating it must meet. We will tell you within a day whether a perimeter-sealed or a fully gasketed IP67 keypad solves it, and ship a sample for the bench. Thank you for reading. We look forward to your inquiry. Best regards, Shanyo team.

Installation and re-sealing

When the sealed keypad is installed on the enclosure, the gasket must be compressed evenly. We recommend a bolt circle around the flange, torqued in a diagonal pattern, so no corner lifts. After a field service, the gasket should be replaced rather than reused, because a once-compressed silicone gasket does not always re-seal. We ship spare gaskets with each production order so the service team has them on the truck.

Send us your control box drawing today.

We are ready to quote your sealed dome array today.

Thank you.

Best wishes.

Sincerely.

Shanyo.

- John Smith, Senior Application Engineer, Shanyo Precision Electronics, Qingdao

Send Inquiry